การพัฒนากลไกสก๊อตโยคเพื่อกำเนิดกระแสการไหลแบบเป็นจังหวะสำหรับการส่งเสริมการถ่ายเทความร้อน : กรณีศึกษาการถ่ายเทความร้อนของไส้กรอก

Main Article Content

ชาญณรงค์ วันทา

Abstract

Abstract


In this paper, the device for generating pulsating flow characteristics was developed for heat-transfer applications. The scotch-yoke mechanism, which is a reciprocating motion mechanism converting a rotational motion into a linear motion was used as the primary mechanism for producing such flows. The scotch-yoke mechanism forces the inlet uniform flow to become a sinusoidal motion, which leads to increased instability in flows. The results of applying unsteady pulsating flows to heat transfer on a sausage show that the influence of pulsating frequency is more significant on heat-transfer enhancement of a sausage. At a low Reynolds number and flow with an optimal pulsating frequency, the temperature of a sausage cools down more than the steady-flow conditions by approximately 14.7 %. The optimal pulsating frequency is found at 2 Hz and an amplitude of 0.35. 


Keywords: heat transfer; food; sine wave; frequency; oscillating flow

Article Details

Section
Engineering and Architecture
Author Biography

ชาญณรงค์ วันทา

ภาควิชาวิศวกรรมเกษตร คณะวิศวกรรมศาสตร์ มหาวิทยาลัยเทคโนโลยีราชมงคลธัญบุรี ตำบลคลองหก อำเภอธัญบุรี จังหวัดปทุมธานี 12110

References

[1] Velayati, E. and Yaghoubi, M., 2005, Numerical study of convective heat transfer from an array of parallel bluff plates, Int. J. Heat Fluid Flow 26: 80-91.
[2] Nsofor, E.C., Celik, S. and Wang, X., 2007, Experimental study on the heat transfer at the heat exchanger of the thermo-acoustic refrigerating system, Appl. Thermal Eng. 27: 2435-2442.
[3] Kim, S.Y., Kang, B.H. and Hyun, J.M., 1998, Forced convection heat transfer from two heated blocks in pulsating channel flow, Int. J. Heat Mass Transfer 41: 625-634.
[4] Suksangpanomrung, A., Chungpaibulpa-tana, S. and Promvonge, P., 2007, Numerical investigation of heat transfer in pulsating flows through a bluff plate, Int. Commun. Heat Mass Transfer. 34: 829-837.
[5] Moon, J.W., Kim, S.Y. and Cho, H.H., 2005, Frequency-dependent heat transfer enhancement from rectangular heated block array in a pulsating channel flow, Int. J. Heat Mass Transfer. 48: 4904-4913.
[6] Ji, T.H., Kim, S.Y. and Hyun, J.M., 2008, Experiments on heat transfer enhance-ment from a heated square cylinder in a pulsating channel flow, Int. J. Heat Mass Transfer. 51: 1130-1138.
[7] Akdag, U., Akcay, S. and Demiral, D., 2014, Heat transfer enhancement with laminar pulsating nanofluid flow in a wavy channel, Int. Commun. Heat Mass Transfer. 59: 17-23.
[8] Wantha, C., 2016, Effect and heat transfer correlations of finned tube heat exchanger under unsteady pulsating flows, Int. J. Heat Mass Transfer. 99: 141-148.
[9] Mikheev, N.I., Molochnikov, V.M., Mikheev, A.N. and Dushina, O.A., 2017, Hydrody-namics and heat transfer of pulsating flow around a cylinder, Int. J. Heat Mass Transfer. 109: 254-265.
[10] Mabie, H.H. and Reinholtz, C.F., 1987. Mechanisms and dynamics of machinery, 4th Ed., John Wiley & Sons, New Jersey.
[11] Richards, K.L., 2014. Design Engineer's Reference Guide: Mathematics, Mechanics, and Thermodynamics. CRC Press.